Part 3 — GED ® Science · Unit 7 — Motion, Forces, and Machines
Unit 7 — Motion, Forces, and Machines
Inside-to-GED Bridge — Laundry Carts, Doors, and Moving Supplies
A loaded laundry cart is harder to accelerate than an empty one under the same net force because it has more mass. A sticky wheel adds friction. A door pivots around hinges, so pushing farther from the hinge usually produces a greater turning effect for the same force. Moving supplies up a ramp trades a smaller force for a longer distance.
These examples do not change the physics vocabulary. Force is measured in newtons, acceleration in meters per second squared, work in joules, and power in watts. Net force requires combining direction. Balanced forces can describe rest or constant velocity.
On the GED® test, the cart may become a block in a diagram. Identify the object, draw or imagine the force directions, calculate net force, and only then use F = ma. Do not grab the biggest number and call it the answer.
Chapter 25 — Describing Motion
GED® test targets: P.b.1, SP.6.a, SP.7.b
Walking from a fictional cell door to the chow entrance and back takes time and effort even if you end exactly where you started. Your displacement is zero, but your distance is not. Physics is not denying the walk happened; it is naming two different measurements. If a question asks one and you calculate the other, the arithmetic can be flawless and the answer still be wrong as hell.
Motion describes a change in position relative to a reference. If you sit on a moving bus, you may be at rest relative to your seat while moving relative to the road. Neither description is automatically wrong; the reference frame determines what is being described.
Distance and displacement answer different questions
Distance is the total length of a path. Displacement is the change from starting position to ending position, including direction. If a model cart moves 5 m east and then 3 m west, it travels 8 m but has displacement 2 m east. Returning to the starting point gives zero displacement without requiring zero distance traveled.
Speed is distance divided by elapsed time. Average velocity is displacement divided by elapsed time and includes direction. An object can have a nonzero average speed and zero average velocity over a round trip. That is not physics being difficult for sport; the two quantities measure different things.
For the 8-m trip completed in 4 s, average speed is 8/4 = 2 m/s. Average velocity is 2/4 = 0.5 m/s east. A question that asks for speed does not want the displacement calculation, even if both use the same time.
Read a position graph
The table gives a cart’s position along a straight track relative to a starting marker.
| Time (s) | Position (m) |
|---|---|
| 0 | 0 |
| 2 | 4 |
| 4 | 8 |
| 6 | 8 |
| 8 | 2 |
From 0 to 4 s, the cart moves in the positive direction at a constant 2 m/s. From 4 to 6 s, its position stays at 8 m, so it is at rest in this reference frame. From 6 to 8 s, position decreases by 6 m, giving velocity −3 m/s. The negative sign indicates direction, not that the cart has somehow traveled less than nothing.

The cart moves outward, rests from 4–6 seconds, then moves back. The falling segment shows negative velocity, not automatically slowing.
The slope of a position-versus-time graph represents velocity. A horizontal segment means constant position. A steeper straight segment means greater speed in magnitude. A downward slope means motion in the negative direction. It does not necessarily mean slowing down.
Acceleration is a change in velocity
Acceleration = change in velocity ÷ elapsed time. If velocity changes from 2 m/s east to 10 m/s east over 4 s, acceleration is (10 − 2)/4 = 2 m/s² east. The unit means velocity changes by 2 meters per second each second during the uniform-acceleration model.
Acceleration can involve speeding up, slowing down, or changing direction. An object moving at constant speed around a curve accelerates because its velocity direction changes. Speed alone does not contain all the information about motion.
A negative acceleration does not always mean slowing down. If velocity is negative and acceleration is also negative, speed increases in the negative direction. For introductory questions, establish a positive direction and compare the signs. Do not let the word negative automatically become “less motion.”
Velocity graphs tell a different story
On a velocity-versus-time graph, slope represents acceleration. A horizontal line at 3 m/s means constant velocity, not rest. A horizontal line at zero means rest. This is why recognizing the axes is more important than recognizing the shape.
For a constant velocity of 3 m/s over 4 s, displacement is 3 × 4 = 12 m. Graphically, that is the rectangular area under the velocity-time line. If velocity is below zero, the signed area contributes negative displacement. Distance requires accounting for the magnitude of motion in each direction.
Worked graph question
Question: In the position table, what happens from 4 to 6 seconds? A. The cart travels at 8 m/s. B. The cart is at rest at position 8 m. C. The cart accelerates continuously. D. The cart returns to zero position.
Answer: B. Position remains 8 m for two seconds. A confuses the position value with a speed. C has no support because the position is unchanged in the model. D contradicts the listed positions. One axis label separates the right answer from a confident wrong one.
A second question asks for total distance over all eight seconds. The cart moves 8 m outward, stays still, then moves 6 m back, totaling 14 m. Its displacement is only 2 m. The answer is not 2 m unless displacement was requested.
Measurement design matters here too
A motion investigation needs a defined start, distance scale, and timing method. If one trial starts timing late, calculated speed can be too high because the recorded time is too small. Repeating trials can reveal variability, but a consistently late start may remain systematic error.
Use the formula as a relationship: greater distance in the same time means greater average speed; the same distance in more time means lower average speed. Before calculating, predict the direction. That quick check catches many answers that are arithmetically neat and physically ridiculous.
Count the Route and the Net Change Separately
Position needs a reference point and a chosen positive direction. Suppose east is positive and the door is zero. Walking 12 m east puts you at +12 m; walking 5 m back leaves you at +7 m. Total distance is 12 + 5 = 17 m, while displacement is final minus initial position: 7 − 0 = +7 m. The sign carries direction, not an automatic judgment about whether the motion is slowing.
Speed uses distance divided by elapsed time. Average velocity uses displacement divided by elapsed time. If that trip takes 10 s, average speed is 17/10 = 1.7 m/s, while average velocity is 7/10 = +0.7 m/s. A full out-and-back trip can therefore have positive average speed and zero average velocity. Both descriptions are true because they answer different questions.
Acceleration is change in velocity per unit time. A cart changing from +2 m/s to +8 m/s in 3 s has acceleration (8 − 2)/3 = +2 m/s². A cart moving east but slowing has negative acceleration under this sign convention. Negative acceleration does not always mean slowing: if both velocity and acceleration are negative, speed can increase toward the west. Direction is not optional fine print.
On a position-time graph, slope represents velocity. On a velocity-time graph, slope represents acceleration and area under the curve represents displacement. In the simple constant-velocity case, 4 m/s for 5 s gives rectangular area 4 × 5 = 20 m. Same visual shape, different axis labels, different meaning. Read the damn axes before launching the calculation.
An unfamiliar robot or animal passage works the same way. Establish the origin, direction, interval, and requested quantity. Then calculate. If a position-time line is flat, the object maintains position; if a velocity-time line is flat above zero, it moves at constant positive velocity. A flat line is not a universal symbol for “nothing is happening.”
Your Turn — Guided and Independent Practice — Practice Check S25
Guided: A cart moves 30 meters east in 10 seconds, then 10 meters west in 5 seconds. Find total distance, displacement, and average speed.
Guided answer: Distance = 30 + 10 = 40 m. Displacement = 20 m east. Total time = 15 s. Average speed = 40/15 ≈ 2.67 m/s. Average velocity would use displacement: 20/15 ≈ 1.33 m/s east.
Inside guided: You walk 1,200 meters in 15 minutes. What is your average speed in meters per second?
Answer: 15 minutes × 60 = 900 seconds. Speed = 1,200 m ÷ 900 s ≈ 1.3 m/s. Slower than it feels, right? Ordinary walking is usually somewhere between 1 and 1.5 meters per second.
Independent: A position-time graph is horizontal for five seconds. What does that mean? A. The object moved backward. B. Speed is increasing. C. Position is constant. D. Time stopped.
Independent answer: C. No position change means zero velocity over that interval. A and B would require a slope; D is ridiculous. Common mistake: reading graph height as speed when the vertical axis is position.