Part 5 — GED ® Mathematical Reasoning · Unit 4 — Q.4 Calculate dimensions, perimeter, circumference, and area of two-dimensional figures
Chapter 19 — Measurement, Scale, Formulas, and Unknown Dimensions
GED® test targets: Q.4.c, Q.3.b; MP.4.b
Inside start: A craft-kit instruction says to cut a strip 18 inches long, but your ruler only shows 12 inches. You convert, then measure. Formulas work the same way: choose the right one, then find the missing piece.
What You’re Going to Learn
You’re going to select and rearrange formulas, use measurement precision appropriately, and combine unit conversions with geometry and scale. A supplied formula isn’t the whole solution. You still have to figure out what the hell each quantity means and which part is missing.
Why This Shit Matters
Many geometry questions provide the formula. Your job is to identify the needed quantities, substitute correctly, and solve for the missing part. Formulas are compact instructions, not slot machines. Identify each variable or the substitution will eat your quarters and hand you a beautifully formatted pile of bullshit.
Key Vocabulary
Formula: an equation expressing a general relationship.
Isolate: use equivalent operations to leave a variable alone.
Precision: the detail of a measurement or reported value.
Approximation: a value close to the exact one.
Constraint: a condition that a solution must satisfy.
Let’s Learn the Damn Mathematics
A fictional community garden has 120 square feet of available space for a rectangular planting bed 10 feet long. The missing width is not a new kind of geometry. The area relationship still says length times width equals area: 10w = 120, so w = 12 feet. Solving backward uses the same relationship as calculating forward. The formula is a map of the relationship. Decide which part of the damn map is missing before trying to drive anywhere.
Write the formula first, then identify each known value with its unit. Rearrange by doing the same operation to both sides. From P = 2l + 2w, subtract 2l and divide by 2 to get w = (P − 2l)/2. From A = bh/2, multiply by 2 and divide by b to get h = 2A/b. A denominator must be nonzero. Physical values such as lengths and areas must also satisfy their contextual constraints. Moving a term is shorthand for an equal operation on both sides, not teleportation, dammit.
Watch out: Scale changes length by k, area by k2, and volume by k3—three different gears, same machine.
Match units before substitution. If a rectangle’s length is 2 feet and width 18 inches, either convert 2 feet to 24 inches or convert 18 inches to 1.5 feet. The area is 432 in2 or 3 ft2. A bare multiplication 2 × 18 = 36 without conversion produces no valid single area unit. The multiplication can be flawless while the measurement is completely screwed. Fix the units first.
A measured length of 8.4 cm reported to the nearest tenth represents an approximate measurement, not infinitely precise knowledge. Follow the question’s rounding instruction. If a circle’s circumference is 31.4 cm and π = 3.14 is specified, d = 31.4/3.14 = 10 cm. More calculator digits aren’t automatically more faithful when the problem deliberately supplies an approximation. Don’t manufacture precision out of thin damn air. Keep intermediate calculations unrounded unless the stated task requires rounding them.
Watch How It Works
Example A — Fictional border constraint. A rectangle has perimeter 50 feet and length 15 feet. Substitute: 50 = 2(15) + 2w. Subtract 30: 20 = 2w. Divide by 2: w = 10 feet. Check 15 + 10 + 15 + 10 = 50. Dividing 50 by 15 would confuse perimeter with area.
Watch out: Unit mismatches survive correct multiplication, so fix them before the numbers get comfortable and start defending their bullshit.
Example B — Scale and area. A floor plan uses 1 cm = 2 m. A rectangle on the plan is 3 cm by 4.5 cm. Real lengths are 6 m and 9 m. Area = 6 × 9 = 54 m2. Check using drawing area 13.5 cm2 and the area conversion 4 m2 per drawing cm2: 13.5 × 4 = 54 m2. The lengths scale first; the area reflects both dimensions changing. Don’t stop at the length factor and shortchange the damn area.
Common Mistakes and How to Avoid Them
Mixing units. Convert every measurement to the same unit before using a formula: 3 feet plus 18 inches is 4.5 feet, not 21.
Scaling area like length. If a drawing doubles every length, the area becomes 4 times as large, not 2 times.
Lesson Summary
Pick the formula that matches the figure, substitute what you know, and solve for the missing piece. Keep units matching, report a sensible precision, and remember that a scale factor k multiplies length by k, area by k2, and volume by k3.
Your Turn — Practice
1. A property-box lid has a perimeter of 84 inches and a length of 26 inches. What is its width?
2. A triangle has an area of 45 m2 and a base of 10 m. Find its height.
3. Every length of a figure is tripled. By what factor does its area change?
Answer check: 1. 84 = 2(26) + 2w, so 2w = 32 and w = 16 in. 2. h = 2A ÷ b = 90 ÷ 10 = 9 m. 3. 32 = 9 times.
Wrong-answer roadmap: If you answered 3 for problem 3, remember that area grows by the square of the scale factor. Reread Example B.